How to make a sphere in Minecraft

Make a sphere or a dome in Minecraft layer by layer: pick the size, hollow or filled, build each layer as a circle, or place it with WorldEdit.

WorldEdit, FastAsyncWorldEditUpdated 13 November 2026

A sphere is the hardest round shape to build by eye: it curves in every direction, most of it is out of reach, and a mistake on one layer shows from the far side of the map. It is also one of the easiest to build from a plan, because a sphere is only a stack of circles. This guide shows how to read a sphere as layers, choose its size and whether it is hollow, build it from the bottom up, cut it into a dome, and when WorldEdit or a schematic saves the climb. The commands are for Java Edition.

What you end up with

A round sphere or dome at the size you want, built layer by layer from a plan that gives every layer's blocks, or placed in one go.

A sphere is a stack of circles

Cut a sphere into horizontal layers one block thick and each layer is a circle. Near the middle the circles are as wide as the sphere and change little from one layer to the next; toward the top and the bottom they shrink fast. Build each layer as a circle of the right size, centred on the same column, and the sphere takes shape on its own.

The sphere and dome generator gives every layer as a grid, with coordinates counted from the centre column, the stretches of blocks along each row and the blocks in the layer, beside a 3D view of the layers built so far. The pictures here are its own.

  1. Layer 1: 21
  2. Layer 2: 24
  3. Layer 3: 24
  4. Layer 4: 28
  5. Layer 5: 28
  6. Layer 6: 28
  7. Layer 7: 28
  8. Layer 8: 28
  9. Layer 9: 24
  10. Layer 10: 24
  11. Layer 11: 21
The 11 layers of an 11-block hollow sphere, bottom to top: 278 blocks. The bottom and top layers are full discs, the middle ones thin rings.Drawn by BlockLab

Pick the size

A sphere's diameter is its width and its height: an 11-block sphere is 11 blocks across and 11 layers tall. Make sure the space has room above as well as around, and remember that blocks cannot go above the world's build limit.

As with circles, an odd diameter has a middle block, so the sphere has a single centre column and a single widest layer. An even diameter has no middle block: its centre column is 2 by 2, and it has two widest layers, one on top of the other. Odd sizes are easier to build by hand, since every layer is measured from one column.

Below about 7 blocks a sphere looks more like a rounded box than a ball; the curve needs room to show. Above 30 or so, every layer takes long enough that a plan, or a tool that places it for you, saves real time.

Hollow or filled

A hollow sphere is a shell, one block thick unless you want it thicker. It keeps the blocks of the sphere that touch the outside above, below or beside them, so it has no gap for light, water or a mob to get through. A thicker shell grows inward and keeps the same outside. A filled sphere is solid all through, for a planet, a boulder or the core of a build; it takes far more blocks.

A 25-block sphere is 1,550 blocks hollow and 8,217 filled. A hollow sphere one block thick takes about 2.5 times its diameter squared, a filled one about half its diameter cubed.

  • Hollow, 28 blocks
  • Filled, 97 blocks
The middle layer of the 11-block sphere, hollow and filled.Drawn by BlockLab

Near the top and bottom of a hollow sphere the layers are full discs, not rings. The shell is almost flat there, so it covers the whole layer, and those layers take as many blocks as on a filled sphere.

Build it layer by layer

  1. Mark the centre column. Build a pillar of a block you will take away later, as tall as the sphere, where its centre goes: one block for an odd diameter, 2 by 2 for an even one. Every layer is measured from it.
  2. Build the bottom layer. It is a small full disc. Read it from the generator's grid at layer 1, counting out from the pillar along each row.
  3. Go up one layer at a time. Move the generator to the next layer and build it on top. Each layer is a circle, so the method from the circle guide applies: mark the four ends, lay one quarter, mirror it.
  4. Reach the upper layers. Scaffolding is the easiest way up: climb it by jumping inside it and come down by sneaking. On a hollow sphere you can also build the upper layers from inside.
  5. Close the top and clear up. The top layer is a small disc like the bottom one. Then take away the pillar and the scaffolding.
The bottom half of the 11-block sphere. Layers 7 to 11 repeat layers 5 to 1.
LayerBlocks acrossHollowFilled
152121
272445
392469
4112889
5112897
6112897

Domes

A dome is the top half of a sphere, cut through its widest layer. It stands on a full circle of its own diameter and, when hollow, is open underneath, which makes it a roof: for a tower, a hall, a greenhouse or an observatory. Its height is half the diameter, rounded up, so an 11-block dome is 6 layers tall: the top 6 layers of the sphere above, 153 blocks hollow.

The dome's first layer is exactly the thin circle of the same diameter. Build a round wall with the circle generator, then a dome of the same size on top, and the two meet with no step. In the sphere generator, choose Dome and build from layer 1 up.

Faster: WorldEdit or a schematic

With WorldEdit or FastAsyncWorldEdit, //sphere makes a filled sphere and //hsphere a hollow one, centred on the block you stand in. They take a radius, so the sphere is twice the radius plus one: a radius of 5 is the 11-block sphere above. Add -r to raise the sphere by its radius, so its bottom is at your feet and it does not dig into the ground.

WorldEdit, in chatClick a line to copy it

WorldEdit's sphere commands make whole, odd spheres. For a dome, an even size or a shell more than a block thick, download the shape from the generator as a .schem and paste it with //schem load and //paste -a: its bottom layer lands at your feet and its centre column where you stand. The schematic guide covers each tool.

Common mistakes

  • Losing the centre. One layer built a block off the centre column tilts everything above it. Keep the pillar until the last layer is in.
  • Building every layer as a ring. On a hollow sphere the layers near the top and the bottom are full discs; built as rings, they leave holes where the shell is flat.
  • Counting layers from the middle. The generator counts layers from the bottom, layer 1 first, so you always know which one comes next.
  • A dome cut in the wrong place. Cut a sphere below its widest layer and the dome bulges out over its base; cut it above and it stands on a narrower circle than the wall under it. The generator's dome is cut through the widest layer.

Where to go next

For walls, towers and floors, How to build a circle in Minecraft covers the single layer in more detail, and the circle generator draws any circle or oval. To shade a dome from one block to another, the gradient generator previews the blend on a dome and exports it as a schematic.